piping questionnaire pdf
Interview Questions Related To pipes Supports:-
1. What are the Criteria for Pipe Supporting?
Following are the points, which should be taken into account for proper supporting: –
A. Load of bare pipe + fluid + insulation (if any).
B. Load of bare pipe + water fill.
C. Load of valves and online equipment and instrument.
D. Thermal loads during operation.
E. Steam out condition, if applicable.
F. Wind loads for piping at higher elevation, if required.
G. Forced vibration due to pulsating flow.
H. Bare pipe with size above 12” shall be supported with Pad or Shoe.
2. What is the basic span of supports for 2”/6”/10”/24” pipe?
Basic Span is 5.5m / 9m / 11.5m / 15m respectively.
3. What is the function of providing the anchor, cross guide and guide for piping?
Anchor is provided to restrict all the axial and rotational movements of pipe, whereas cross guide is
provided to restrict displacements of pipe along with the axis perpendicular to its centerline and Guide is provided to restrict the longitudinal movements of pipes along with its axis.
4. How is piping to Tank inlet nozzle is supported and why?
Piping to Tank Nozzle is supported with spring type support (first support from Nozzle) in order to
make the nozzle safe from the loads which occurs due to the displacement of pipe ( Displacement
may be due to thermal expansion of pipe, tank material, tank settlement etc).
5. What are the types of flexible spring hangers?
1. Constant Spring Hanger 2. Variable Spring Hanger.
6. What is the purpose of providing Graphite Pads in supports below shoes?
To reduce the friction factor. The coefficient of friction for Graphite Pads is 0.1
7. Where do you provide Anchor and Slotted Support of Heat Exchanger?
Anchor support of Heat exchanger is provided on the side from which Tube bundle will be pulled out for the purpose of maintenance work also it is based on the growth of the connecting piping as
exchanger should grow with the piping.
8. What should be the material of shoes for supporting AS pipes & why?
If CS shoes are used then pad in contact with the pipe shall be of Alloy steel to avoid dissimilar
welding at pipe. To avoid alloy steel welding and dissimilar welding, fabricated clamps either of CS or SS can be used.
9. What are sway braces?
Sway braces are essentially a double acting spring housed in a canister. Their purpose is to limit the
undesirable movement. Undesirable movement means movement caused by wind loading, rapid
valve closure, relief valve opening, two phase flow or earthquake.
10. What is the difference between variable spring hanger and constant spring hanger?
Variable spring Hanger: –
As the name itself indicates the resistance of the coil to a load changes during compression.
Constant spring Hanger: –
Constant spring hanger provides constant support force for pipes and equipment subjected to vertical movement due to thermal expansion.
This entry was posted in Interview Questions and Answers, Piping Interview Questions Answers and tagged Bergen Power Pipe Supports Interview Questions, interview questions on piping projects, mechanical piping interview questions, Pipe Interview Questions, Piping Design Engineer Interview Point Questions, piping foreman interview questions and answers, piping foreman interview questions pdf, Piping interview Q&A | Piping Engineer, Piping interview questions, piping interview questions with answers, piping qc inspector interview questions, piping questionnaire pdf, piping questionnaire pdf free download, Piping Stress Job Interview Questions, piping supervisor interview questions and answers, Piping Support Interview Question, Piping Text into Questions and Answers, Question and Answers on Piping related topics, Questions Related to Pipes Supports, Searches related to Interview Questions Related To Pipes Supports, Typical Questions For Piping Engineer's Knowledge Testing, Westinghouse Pipe Support Engineer Interview Questions, What are technical questions for piping?.
Questions Answers Related to Codes & standard: –
1. Q:-What is the ASME code followed for design of piping systems in Process piping (Refineries
& Chemical Industries)?
(i) B 31.1
(ii) B 31.3
(iii) B 31.5
(iv) B 31.9
2. Q:-Which American institute standard does piping engineer refer?
A. The American Petroleum institute (API).
B. The American Iron & Steel institute (AISI).
C. The American Society for Testing and materials (ASTM).
D. The American National standard institute (AISI).
E. The American welding society (AWS).
F. The American Water Works Association (AWWA).
G. The American Society for Mechanical Engineers (ASME).
3. Q:-What is the different ASME 31 code for pressure piping?
A. ASME B31.1 – Power piping.
B. ASME B31.2 – Fuel Gas Piping.
C. ASME B31.3 – Process piping.
D. ASME B31.4 – Pipeline Transportation system for liquid hydrocarbon & other liquid.
E. ASME B31.5 – Refrigeration Piping.
F. ASME B31.8 – Gas transmission & distribution piping system.
G. ASME B31.9 – Building services piping.
H. ASME B31.11 – Slurry transportation piping system.
4. Q:-What are the different sections of ASME code? Where these sections are referred?
A. ASME section I : – Rules for construction of power boiler.
B. ASME Section II : – Materials.
Part A – Ferrous materials.
Part B – Non-Ferrous materials.
Part C – Specification for electrodes & filler wire.
Part D – Properties.
C. ASME Section IV : – Rules for construction of Heating Boiler.
D. ASME Section V : – Non- destructive Examination.
E. ASME Section VI : – Recommended rules for care & operation of heating boiler.
F. ASME Section VII : – Recommended guidelines for care of power boiler.
H. ASME Section VIII : – Rules for construction of pressure vessels. (Division I & II)
I. ASME Section IX : – Welding & Brazing qualification.
5. Q:-Which American standard is reffered for selection of following piping element?
A. Flanges B. Butt Welded fittings C. Gasket D. Socket & Threaded fittings
E. Valves F. Pipes.
A. Flanges :-
I. ASME B16.1 : – Cast iron pipes flanges & flanged fittings.
II. ASME B16.5 : – Carbon steel pipes flanges & flanged fittings. (Up to 24”)
III. ASME B16.47 : – Large Diameter steel flanges. (Above 24”)
B. Butt welded fittings :-
I. ASME B16.9 : – Steel butt welding fittings.
II. ASME B16.28 : – Butt-welded short radius elbows & returns bends.
C. Gasket :-
I. ASME B16.20 / API -601: – Metallic gaskets for pipe flanges- Spiral wound,
Octagonal ring Joint & Jacketed flanges.
II. ASME B16.21 : – Non metallic gasket.
D. Socket & Threaded fittings :
I. ASME B16.11 : – Forged steel socket welding & threaded fittings.
E. Valves :-
I. ASME B16.10 : – Face to face & end to end dimension of valves.
II. ASME B16.34 : – Flanged & butt-welded ends steel valves (Pressure &Temperature ratings)
except Ball, Plug & Butter fly Valves.
F. Pipes :-
I. ASME B36.10 : – Welded & Seamless wrought iron pipes.
II. ASME B36.19 : – Stainless steel pipes.
If you are Interested to attend our AWS CWI Seminar, Please Fill the Enquiry Form:
This entry was posted in Piping Interview Questions Answers and tagged 11 most important questions & answers from ASME B, interview questions on piping projects, pdms piping designer interview questions, Piping Design Engineer Interview Questions, piping design interview questions and answers pdf, Piping interview questions, PIPING INTERVIEW QUESTIONS PART 1, piping questionnaire pdf, piping questions and answers pdf free download, piping related question and answer, piping supervisor interview questions and answers, Searches related to Piping Interview Questions Answers Related to Codes & standard, sp3d piping interview questions, Top 10 piping interview questions with answers.